[. . . ] Table of Contents Table of Contents Product Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Hardware Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The administrator password has read/write access. Password: Enter a new password for the Admin User Name. Verify Enter the same password that you entered in the Password: previous textbox in order to confirm its accuracy. Enables a challenge-response test which will Enable require users to type letters or numbers from Graphical a distorted image displayed on the screen Authentication: to prevent online hackers and unauthorized users from gaining access to your device’s configuration. This feature is disabled by default. D-Link DHP-W307AV User Manual 40 Section 3 - Configuration System Save to Local Use this option to save the current access point Hard Drive: configuration settings to a file on the computer you are using. You will then see a file dialog where you can select a location and file name for the settings. Upload from Local Use this option to load previously saved access Hard Drive: point configuration settings. Then, click the Upload Settings button to transfer those settings to the access point. Restore to Factory This option will restore all configuration settings Default: back to the settings that were in effect at the time the access point was shipped from the factory. Any settings that have not been saved will be lost, including any rules that you have created. If you would like to save the current access point configuration settings, use the Save button above. Note: Restoring the factory default settings will not reset the Wi-Fi Protected Status to Not Configured. Reboot the Device: Click to reboot the access point. D-Link DHP-W307AV User Manual 41 Section 3 - Configuration Firmware You can upgrade the firmware of the access point from this page. Make sure the firmware you would like to use is on the local hard drive of your computer. Please check the D-Link support site for firmware updates at http://support. dlink. com. You can download firmware upgrades to your hard drive from the D-Link support site. Firmware Click on the Check Now button to find out if there Information: is an updated firmware or language pack version. If a new version exists, download the new firmware to your hard drive. Firmware After you have downloaded the new firmware, click Upgrade: Browse to locate the firmware update on your hard drive. Language Pack To upgrade the language pack, follow these steps: Upgrade: 1. Click the Browse button to locate the D-Link language pack upgrade file on your computer. Note: Language pack file extension will be *. lng 2. Once you have found the file, click the Upload button to begin the language pack upgrade process. This process can take about 75 seconds. D-Link DHP-W307AV User Manual 42 Section 3 - Configuration Time The Time Configuration option allows you to configure, update, and maintain the correct time on the internal system clock. Daylight Saving can also be configured to automatically adjust the time when needed. Time Zone: Select the Time Zone from the drop-down menu. To select Daylight Saving time manually, click Daylight Saving: the Enable Daylight Saving check box. [. . . ] Eliminate Interference Place home appliances such as cordless telephones, microwaves, wireless speakers, and televisions as far away as possible from the bridge/access point. This would significantly reduce any interference that the appliances might cause since they operate on same frequency. D-Link DHP-W307AV User Manual 77 Appendix A - Wireless Basics Security Don’t let your next-door neighbors or intruders connect to your wireless network. Secure your wireless network by turning on the WPA, WPA2, or WEP security feature on the access point. Refer to product manual for detail information on how to set it up. Wireless Modes There are basically two modes of networking: • Infrastructure – All wireless clients will connect to an access point or wireless bridge. [. . . ]